How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Just how do you actually feel with regards to Installing A Bathtub?
Mounting a bath tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably tough job. If the old tub is easily accessible, the project can move speedily; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the work and fit attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is far better to consider utilizing one before you start. Chances are you might need a specialist plumber to make tube links.
This post will certainly assist you install a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and do not need to alter the plan of your previous supply of water pipes.
Your tools as well as product checklist ought to comprise the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level reviews degree.
To mount taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bath tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been made use of at least when as this will certainly settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Protect the faucet in place with the producer offered backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting about Installing A Bathtub when surfing the internet. Enjoyed reading our post? Please share it. Let somebody else find it. I cherish reading our article about Tools You Need to Install a New Bathtub .
Request An Estimate Report this page